Rm-materials-handling VARIABLE SPEED CONTROLS ControlMaster Plus Service Bedienungsanleitung PDF herunterladen (Seite 31)

R&M Materials Handling, Inc.

4501 Gateway Boulevard

Springfield, Ohio 45502

P.: (937) 328-5100

FAX: (937) 325

5319

31/83

R&M Materials Handling, Inc. reserves the right to alter or amend the above information without notice.

Min Freq Offset P2.4.8

Parameter defines how much below minimum frequency can correction to

frequency output of the drive be made.

0,00 – 20,00 Hz

SystemBus Speed P2.4.9. SystemBus communication speed. Default = 3 Mbit/s 0 = 1,5 Mbit/s

1 = 3 Mbit/s

2 = 6 Mbit/s

3 = 12 Mbit/s

Max Pos Error V2.4.10.1. Current position error of the hoist with the largest displacement to

synchronization reference position. Only master unit displays this

information.

Pos Error 1-4 V2.4.10.2-5 Unit 1-4 current position error to Synchro position. Only master unit

displays this information.

Peak Pos Error 1-4 V2.4.10.6-9 Unit 1-4 peak position error to Synchro position since last power off. Only

master unit displays this information.

Synchro Status V2.4.10.10. 0 0 0 0 0 00000-11111

1=SystemBus

address >0

Nominal speed >0

SSU board OK

1=SystemBus

working properly

1= Unit is a Master

1= Unit is a Follower

1=Synchro is active

in this station

G4. Monitoring

G4.1 Parameter backup

Load Default Par B4.1.1 Restores Default Parameters to Active Parameters from the Control Unit

memory. Default Parameters are the parameters, which have been saved

in the factory.

Save User Par B4.1.2 Saves Active Parameters in the Control Unit as User Parameters. Final

parameters for the application must be saved as User Parameters after

start-up.

Load User Par B4.1.3 Restores User Parameters to Active Parameters from the control unit

memory. User Parameters are the parameters, which have been saved

after start-up.

G4.1.4 Factory Default

Save Default Par B4.1.4.1 Saves Active Parameters in the Control Unit as Default Parameters.

Default Parameters are the parameters, which must be saved in the

factory. For factory use only.

G4.2 Analog I/O

Ain1 Value V4.2.1 Value of analog input Ain1 0 – 10 V

Ain2 Value V4.2.2 Value of analog input Ain2 0 – 10 V

Aout1 Value V4.2.3 Value of analog output Aout1 0 – 20 mA

Aout2 Value V4.2.4 Value of analog output Aout2 0 – 10 V

G4.3 Relay output

ROB1 State V4.3.1 State of relay output ROB1 0=OFF, 1=ON

ROB2 State K7 V4.3.2 State of relay output ROB2, K7 0=OFF, 1=ON

ROC1 State V4.3.3 State of relay output ROC1 0=OFF, 1=ON

ROD1 State V4.3.4 State of relay output ROD1 0=OFF, 1=ON

ROE1 State V4.3.5 State of relay output ROE1 0=OFF, 1=ON

ROE2 State V4.3.6 State of relay output ROE2 0=OFF, 1=ON

ROE3 State V4.3.7 State of relay output ROE3 0=OFF, 1=ON

G4.4 Operate counters

Not used

G4.5. Fault Counter

Fault Counter V4.5.1. – 4.5.24 Fault counter value.

Other faults V4.5.25 Other faults

Total Faults V4.5.26

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 82 83

Kommentare zu diesen Handbüchern

Keine Kommentare

Rm-materials-handling VARIABLE SPEED CONTROLS ControlMaster Plus Service Bedienungsanleitung Seite 31

Kommentare zu diesen Handbüchern